|
|
|
|
|
|
|
|
|
|
|
|
|
|
Standard compression sleeve for 1/4" O.D. copper tube.
|
Standard compression sleeve and nut for 1/4" O.D. copper tube. 2 nuts and 2 sleeves.
|
Includes slip in, non-threaded overflow pipe, washer, poly drain with 3/4" male garden hose threads.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set of 2 for standard 2-1/2" resilient motor mounting rings.
|
1/4" cc x 1/8" MPT. Use with copper or poly tube on side tapped sill cock or pipe adapter. Includes poly tube adapter.
|
Adapts poly tube to brass fittings without using 1/4" cc sleeve.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fits all Offset and Concentric pumps.
|
Union for 1/4'' O.D. copper tubes.
|
Prevents sagging and movement. Replacement for Champion Coolers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Prevents sagging and movement. Replacement for Artic Circle, Arvin and Mcgraw.
|
1/2'' MPT overflow pipe with flat sided hex head for easy install and removal. Washer included. Nylon drain with 1/2'' FTP I.D. and 3/4'' male garden hose threads O.D.
|
Formed basket, fits all pumps. 8"L x 6"W x 3-1/2"H.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For cooler bearings and some cooler motors with oilable bearings. Lubricate shaft bearings at the start of every season and every 60 days during season. Inhibits rust and oxidation.
|
A time release formula that controls unpleasant odors from algae and bacteria in evaporative coolers, and neutralizes odor in cooler water to freshen cooler air. Can be divided 4 ways. Not for potable water.
|
Provides a one step treatment to inhibit buildup of scale, rust, and offensive odor. Conditions cooler pad to reduce air temperature. Contains mild acid and wetting agents, not for potable water.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4"cc x 1/4"cc x 1/4"cc Tee, for connecting two coolers to one water source. Includes poly tube adapters.
|
Standard for residential and commercial pumps with 4,500 to 11,000 CFM ratings. Use to run water from pump to distributor.
|
Kit fits 3 way side, 4 way down, 6 way side and 8 way down by using an 8 way down distributor with up to 5 inserts plugs and MEK. Includes distributor head, water distributor adapter, MEK solvent and instructions.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4" cc x 1/8 MPT straight water shut-off valve. Includes poly tube adapter.
|
1/4" cc x 1/8 MPT Angle water shut off valve. Includes poly tube adapter, fits sill cocks and pipe adapter.
|
Dial Pillow Block Bearing, Suitable For Use With: Evaporative Cooler Purge Systems, 5/8 in Diameter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4" cc x 1/4" cc straight in line water shut-off valve. Includes poly tube adapters for 1/4" poly tube.
|
20-1/8" end to bend length. Fits all residential coolers.
|
Brass inlet, arm and stem. Polypropylene body and float. Noiseless and noncorrosive.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Provides a one step treatment to inhibit buildup of scale, rust, and offensive odor. Conditions cooler pad to reduce air temperature. Contains mild acid and wetting agents, not for potable water.
|
Premium, heavy-bodied, "one coat" coating. Apply with a brush. Designed to coat and seal evaporative cooler bottom pans, protect against rust and corrosion all season, help deaden sound. Resistant to moisture, non-asbestos and fast drying.
|
Dial Pillow Block Bearing, Suitable For Use With: Evaporative Cooler Purge Systems, 3/4 in Diameter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dial Pillow Block Bearing, Suitable For Use With: Evaporative Cooler Purge Systems, 1 in Diameter
|
Rests in cooler pan water. Controls scale buildup and corrosion in coolers. Holds minerals in suspension by raising the solubility level of the water, reducing mineral buildup on pads. Must be used with bleed off kit or PowerClean purge pump to flush suspended minerals. Lasts all season, easy to install.
|
Includes: distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.
|
|
|
